Linde HPV-02 hydraulipumppu – tehokas, kestävä, monipuolinen
The Linde HPV-02 is an extremely effective hydraulic pump that is ideal for a variety of applications. It can be used with all types of pumps, including reciprocating, rotary, and centrifugal pumps. The Linde HPV-02 has been designed to last for years without needing to be replaced or repaired. It is one of the most durable pumps on the market today.
The Linde HPV-02 was designed to handle tough environments and high temperatures without any problems. It can operate at temperatures ranging from -40 degrees Fahrenheit up to 250 degrees Fahrenheit. This makes it ideal for use in areas where temperatures fluctuate widely during the day or night.
The design of this pump allows it to handle high levels of pressure while still operating smoothly and quietly. It can handle pressures up to 100 psi without any problems and can also operate at a flow rate of 25 gallons per minute (GPM) when operating at full capacity.
The Linde HPV-02 Hydraulic Pump is a load-sensing single pump that is designed to meet the highest efficiency, performance and availability standards.
The HPV-02 is available in a variety of shaft options, allowing it to be easily integrated into most system configurations. It can be installed vertically or horizontally and can be used in applications ranging from agricultural machinery to mining equipment.
The HPV-02 has an internal relief valve with a spring-loaded pressure relief valve (PRV) that opens at 10 bar. The relief valve also helps protect the pump from damage caused by overpressurization of the hydraulic circuit.
The Linde HPV-02 is highly efficient, achieving savings of up to 10 percent in fuel consumption compared with other competitive products.
The pump was developed by Linde Hydraulics, a division of Linde Engineering, in response to the increasing demand for higher performance and greater energy efficiency from the industry.
The Linde HPV-02 is designed for use on low-rpm, high-flow hydraulic applications such as mining dump trucks, excavators and hydraulic hammers. The hydraulic pump offers improved hydraulic efficiency over previous generations of Linde hydraulic pumps, resulting in fewer emissions and less wear on engines.
”We are pleased to offer this new generation of hydraulic pump that significantly reduces fuel consumption,” says Jim Folsom, vice president of hydraulics at Linde Engineering North America. ”The new design represents years of research and development focused on reducing overall power consumption while maintaining high flow rates.”
Linde offers the HPV-02 as a complete system consisting of a variable displacement pump, high pressure gear pump (optionally available) and steering distributor.
The Linde HPV-02 is one of the most competitively priced systems. It offers a high power density and high efficiency with a low emissions level. The system is designed for heavy duty applications such as cranes and mobile drilling rigs where a high power to weight ratio is required.
The Linde HPV-02 was developed in close cooperation with our customers. The result is an innovative product meeting the requirements of modern mobile equipment.
All components of the LHPV-02 are designed to work together as a matched set.
The Linde HPV-02 Hydraulic Pump is designed to be used in applications where high pressure, high flow and low noise are required. This hydraulic pump delivers a maximum flow rate of 20 m3/h at pressures up to 2200 bar, making it ideal for industrial applications such as shipbuilding, construction and mining. The Linde HPV-02 is available in both single acting and double acting versions.
The Linde HPV-02 has been designed specifically for use in harsh environments, making it ideal for use in offshore oil & gas production sites or heavy industry where there is a risk of fire or explosion. The Linde HPV-02 offers a number of safety features including an automatic thermal overload protection system (ATOPS) that shuts down the hydraulic pump if it overheats due to excessive pressure or flow rates which can lead to serious damage or failure of the equipment. The ATOPS system also ensures that the hydraulic pump does not restart until it has cooled sufficiently so that any residual heat does not cause further damage when operating again
Most mobile machinery manufacturers already use a combination of fixed and variable pumps in their hydraulic systems.
Most mobile machinery manufacturers already use a combination of fixed and variable pumps in their hydraulic systems. Fixed displacement pumps are used for low pressure applications on equipment with a low flow rate. Variable displacement pumps are used for high pressure applications where flow needs to be adjusted depending on load requirements.
Variable displacement hydraulic pumps allow for fine control over the flow rate of the system and can be electronically controlled for accurate pressure regulation. This means that these pumps can achieve a much higher efficiency than fixed displacement units, which means they use less energy to operate, resulting in reduced fuel consumption and improved operator comfort levels – perfect for mobile equipment operators!
In addition to optimizing overall fuel economy, variable pumps give manufacturers another option for reducing their machines’ environmental impact, by helping to reduce exhaust gas emissions and noise levels.
With variable pumps, manufacturers can optimize the pump speed at each operating point, thus optimizing overall fuel economy. In addition to optimizing overall fuel economy, variable pumps give manufacturers another option for reducing their machines’ environmental impact, by helping to reduce exhaust gas emissions and noise levels.
The HPV-02 hydraulic pump is designed for hydraulic applications where a high flow rate is required. This pump is suitable for use on tractors and excavators as well as other mobile machinery with a high demand for power.
The Linde HPV-02 pump offers numerous benefits to mobile equipment manufacturers looking for energy efficiency, versatility and a durable design
The Linde HPV-02 hydraulic pump offers numerous benefits to mobile equipment manufacturers looking for energy efficiency, versatility and a durable design. This pump is designed with a high-pressure piston pump that delivers up to 3,000 psi at 300 gpm. It has a unique design that provides an integral fluid cooler and oil cooler, which reduces maintenance costs by reducing the amount of time it takes to heat up an engine.
The Linde HPV-02 hydraulic pump also comes with a high-pressure venturi system that provides optimal performance at low temperatures. The pump comes with a single or double stage system that can be configured in either parallel or series operation depending on your needs.
The Linde Hydraulic Pump is a good choice if you’re looking to add versatility to your operations. This pump can be used in a variety of applications, whether for making grain bins or for powering a hog mixer. It’s also durable and high-performance, which bodes well for years of operation. Most farmers would agree that the Linde HPV-02 Hydraulic Pump is definitely a force to be reckoned with.
